I think I recall posting or seeing something similar here many years ago...
But rather than going back in time, let's just revisit these again.
Old No7
COMMON TOOLS AND THEIR USAGE:
SKILL SAW
A portable cutting tool used to make boards too short.
BELT SANDER
An electric sanding tool commonly used to
convert minor touch-up jobs into major refinishing jobs.
WIRE WHEEL
Cleans paint off bolts and then throws them
somewhere under the workbench with the speed of light. Also removes fingerprints and hard-earned calluses from fingers in about the time it takes you to say, 'Oh ****'. Will easily wind a tee shirt off your back
DRILL PRESS
A tall upright machine useful for suddenly snatching flat metal bar stock out of your hands so that it smacks you in the chest and flings your beer across the room, denting the freshly-painted project which you had carefully set in the corner where nothing could get to it.
CHANNEL LOCKS
Used to partially round off bolt heads. Sometimes used in the creation of blood-blisters.
HACKSAW
One of a family of cutting tools built on the Ouija board principle. It transforms human energy into a crooked, unpredictable motion, and the more you attempt to influence its course, the more dismal your future becomes.
VISE-GRIPS
Generally used after Channel Locks to completely round off bolt heads. If nothing else is available, they can also be used to transfer intense welding heat to the palm of your hand.
OXYACETYLENE TORCH
Used almost entirely for igniting various flammable objects in your shop and creating a fire. Also handy for igniting the grease inside the wheel hub out of which you want to remove a bearing race.
TABLE SAW
A large stationary power tool commonly used to launch wood projectiles for testing wall integrity. Very effective for digit removal!
HYDRAULIC FLOOR JACK
Used for lowering an automobile to the ground after you have installed your new brake shoes, trapping the jack handle firmly under the bumper.
BAND SAW
A large stationary power saw primarily used by most shops to cut large pieces into smaller pieces that more easily fit into the trash after you cut on the inside of the line instead of the outside edge. Also (as with the Table Saw) excels at amputations.
TWO-TON ENGINE HOIST
A tool for testing the maximum tensile strength of all the **** you forgot to disconnect.
PHILLIPS SCREWDRIVER
Normally used to stab the vacuum seals under lids or for opening old-style paper-and-tin oil cans and splashing oil on your shirt; but can also be used, as the name implies, to strip out Phillips screw heads.
STRAIGHT SCREWDRIVER
A tool for opening paint cans. Sometimes used to convert common slotted screws into non-removable screws and butchering your palms.
PRY BAR
A tool used to crumple the metal surrounding that clip or bracket you needed to remove in order to replace a 50 cent part.
PVC PIPE CUTTER
A tool used to make plastic pipe too short.
HAMMER
Originally employed as a weapon of war, the hammer nowadays is used as a kind of divining rod to locate the most expensive parts adjacent to the object you are trying to hit. Also very effective at delayed fingernail removal.
UTILITY KNIFE
Used to open and slice through the contents of cardboard cartons delivered to your front door. Works particularly well on contents such as seats, vinyl records, liquids in plastic bottles, collector magazines, refund checks, and rubber or plastic parts. Especially useful for slicing work clothes, but only while in use. These can also be used to initiate a trip to the emergency room so a doctor can stich up the damage.
SON OF A ***** TOOL
Any handy tool that you grab and throw across the garage while yelling 'Son of a *****' at the top of your lungs. It is also, most often, the next tool that you will need.
Common Tools and Their Usage
Forum rules
Welcome to the Leverguns.Com General Discussions Forum. This is a high-class place so act respectable. We discuss most anything here other than politics... politely.
Please post political post in the new Politics forum.
Welcome to the Leverguns.Com General Discussions Forum. This is a high-class place so act respectable. We discuss most anything here other than politics... politely.
Please post political post in the new Politics forum.
Common Tools and Their Usage
"Freedom and the Second Amendment... One cannot exist without the other." © 2000 DTH
-
- Advanced Levergunner
- Posts: 6972
- Joined: Tue Apr 03, 2007 8:52 pm
- Location: Ridgefield WA. USA
- gamekeeper
- Spambot Zapper
- Posts: 17457
- Joined: Thu Sep 06, 2007 3:32 pm
- Location: Over the pond unfortunately.
Re: Common Tools and Their Usage
I hate to admit it but a lot of that sounds familiar......
Whatever you do always give 100%........... unless you are donating blood.
Re: Common Tools and Their Usage
Heh... A good list of tools. Must have been written by an "engineer".
Government office attracts the power-mad, yet it's people who just want to be left alone to live life on their own terms who are considered dangerous.
History teaches that it's a small window in which people can fight back before it is too dangerous to fight back.
History teaches that it's a small window in which people can fight back before it is too dangerous to fight back.
-
- Senior Levergunner
- Posts: 1049
- Joined: Wed Jan 28, 2009 9:12 pm
- Location: Bushwhacker Capitol, Missouri
Re: Common Tools and Their Usage
Corb Lund wrote a song about that. https://www.youtube.com/watch?v=CwGrC0KicSo
Re: Common Tools and Their Usage
Measure twice, cut once.
Mark
Mark
-
- Senior Levergunner
- Posts: 1429
- Joined: Sat Jan 01, 2011 2:42 am
- Location: mechanicsville, md.
Re: Common Tools and Their Usage
my brother-in-law knows about the table saw.
Rossi 92 .357 lever , and a cz pcr 9mm
Henry .22 lever, Remington speedmaster 552 .22 lr
Marlin Glenfield .22 boltaction
gforce 12ga semi
Taylor's Tactical 1911 A1 FS in .45acp
winchester 1873 44.40
Marlin 336W .30.30
beeman sportsman rs2 dual caliber pellet rifle
henry .22 magnum pumpaction/octagon barrel
stag 5.56 m4 with reddot
Henry .22 lever, Remington speedmaster 552 .22 lr
Marlin Glenfield .22 boltaction
gforce 12ga semi
Taylor's Tactical 1911 A1 FS in .45acp
winchester 1873 44.40
Marlin 336W .30.30
beeman sportsman rs2 dual caliber pellet rifle
henry .22 magnum pumpaction/octagon barrel
stag 5.56 m4 with reddot
Re: Common Tools and Their Usage
Hmmm. As a lifelong machinist/mechanic I an too familiar with most of those tools. I still have scars from a drill press that turned a piece of flat stock into a "flesh eater" (a blade doing 900 RPM hurts!)...
Mike
Vocatus atque non vocatus, Deus aderit...
I've learned how to stand on my own two knees...
Vocatus atque non vocatus, Deus aderit...
I've learned how to stand on my own two knees...